PRISM Series Firmware Release – V3.5.4

• MPI and MPX that have been upgraded to 25G
• MPI2-10 and MPX2-10 that have been upgraded to 25G
• MPI2-25 and MPX2-25
• MPS-100/200/300
• MPD-100/200/300

• MPI and MPX without 25G upgrade
• MPI2-10 and MPX2-10 without 25G upgrade

• New ST2110 video monitor and generator formats:
  • 2048x1080 4:2:2 YCbCr 10b 23p, 24p, 25p, 29p, 30p
  • 4096x2160 4:2:2 YCbCr 10b 23p, 24p, 25p, 29p, 30p
  • 1920x1080 4:4:4 RGB 12b 23p, 24p, 25p, 29p, 30p
  • 2048x1080 4:4:4 RGB 12b 23p, 24p, 25p, 29p, 30p
  • 3840x2160 4:4:4 RGB 12b 23p, 24p, 25p, 29p, 30p
  • 4096x2160 4:4:4 RGB 12b 23p, 24p, 25p, 29p, 30p
• New HDR, Audio and EBU R103 alarms
• New Immersive PCM audio support for SDI and IP including 5.1.4 / 7.1.4 surround sound display
• Support for audio programs that are split across multiple ST2110-30 streams
• Support for dual HDMI receivers on DP ports in MPX2 models.

Release Notes – V3.5.4

Installation Instructions

PRISM Series Firmware Release – V3.3.3

• MPI and MPX that have been upgraded to 25G
• MPI2-10 and MPX2-10 that have been upgraded to 25G
• MPI2-25 and MPX2-25
• MPS-100/200/300
• MPD-100/200/300

• MPI and MPX without 25G upgrade
• MPI2-10 and MPX2-10 without 25G upgrade

• There are no new features or resolved defects in this release. This release is intended for products that have hardware platform changes. See Release Notes for details.

Release Notes – V3.3.3

Installation Instructions

PRISM Series Firmware Release – V3.3.2

• MPI and MPX that have been upgraded to 25G
• MPI2-10 and MPX2-10 that have been upgraded to 25G
• MPI2-25 and MPX2-25
• MPS-100/200/300
• MPD-100/200/300

• MPI and MPX without 25G upgrade
• MPI2-10 and MPX2-10 without 25G upgrade

• MPI2-25 with serial number starting at S010564
• MPX2-25 with serial number starting at S010386
• All MPS/MPD products

• Persistent NMOS Receiver with user configurable target input. (Refer to the v3.3.2 User Manual for details)

Release Notes – V3.3.2

Installation Instructions

PRISM Series Firmware Release – V3.3.1

• MPI and MPX that have been upgraded to 25G
• MPI2-10 and MPX2-10 that have been upgraded to 25G
• MPI2-25 and MPX2-25
• MPS-100/200/300
• MPD-100/200/300

• MPI and MPX without 25G upgrade
• MPI2-10 and MPX2-10 without 25G upgrade

• MPI2-25 with serial number starting at S010564
• MPX2-25 with serial number starting at S010386
• All MPS/MPD products

• New ST2110 formats:
  • 1280x720, 23.98/24/25/29.97/30/50/59.94/60p, YCbCr 4:2:2, 10bit
  • 1920x1080, 23.98/24/25/29.97/30p, YCbCr 4:2:2, 10bit
  • 2048x1080, 23.98/24/25/29.97/30/50/59.94/60p, YCbCr 4:2:2, 10bit
  • 3840x2160, 23.98/24/25/29.97/30/50/59.94/60p, YCbCr 4:2:2, 10bit
  • 4096x2160, 23.98/24/25/29.97/30/50/59.94/60p, YCbCr 4:2:2, 10bit
• New SDI formats:
  • 1280x720, 23.98/24/25/29.97/30/50/59.94/60p, YCbCr 4:2:2, 10bit
  • 1920x1080, 23.98/24/29.97/30p, RGB 4:4:4, 12bit
  • 2048x1080, 23.98/24/25/29.97/30/47.95/48/50/59.94/60p, YCbCr 4:2:2, 10bit
  • 2048x1080, 23.98/24/29.97/30p, RGB 4:4:4, 12bit
  • 3840x2160, 23.98/24/29.97/30p, RGB 4:4:4, 12bit
  • 4096x2160, 23.98/24/25/29.97/30/47.95/48/50/59.94/60p, YCbCr 4:2:2, 10bit
  • 4096x2160, 23.98/24/29.97/30p, RGB 4:4:4, 12bit
• New ST2110 IP Generator formats:
  • 1280x720, 23.98/24/25/29.97/30/50/59.94/60p, YCbCr 4:2:2, 10bit
  • 1920x1080, 23.98/24/25/29.97/30p, YCbCr 4:2:2, 10bit
  • 2048x1080, 23.98/24/25/29.97/30/50/59.94/60p, YCbCr 4:2:2, 10bit
  • 3840x2160, 23.98/24/25/29.97/30/50/59.94/60p, YCbCr 4:2:2, 10bit
  • 4096x2160, 23.98/24/25/29.97/30/50/59.94/60p, YCbCr 4:2:2, 10bit
• ST2110-20 fast input switching to improve switching times between IP programs
• AV Delay Measurement for SDI, ST2022-6 and ST2110-20/30/31
• Dolby E/ED2 Guard Band measurement against house black burst signal
• Dolby ED2 meta data decoding
• User configurable Audio Test and Program Peak Level setting
• Audio channel labeling for 7.1.4
• Picture Safe Area and AFD graticules
• Colorized traces in Parade mode for Waveform and Stop displays
• Floating Time Code overlay
• Additional format support for ST2110-21

Release Notes – V3.3.1

Installation Instructions

PRISM Series Firmware Release – V3.1.1

• MPI and MPX that have been upgraded to 25G
• MPI2-10 and MPX2-10 that have been upgraded to 25G
• MPI2-25 and MPX2-25
• MPS-100/200/300
• MPD-100/200/300

• MPI and MPX without 25G upgrade
• MPI2-10 and MPX2-10 without 25G upgrade

• MPI2-25 with serial number starting at S010564
• MPX2-25 with serial number starting at S010386
• All MPS/MPD products

• Multi SDI Input Mode
  • Up to four 4K 6/12G SDI inputs can be simultaneously monitored with picture and trace applications (waveform, stop, vector, CIE).

• NMOS IS-04 v1.3
  • IS-04 v1.2 or v1.3 can be selected

• GPI Preset Recall
  • Up to 6 presets can be recalled through GPIO connector.

• SDI Loop-through
  • SDI 1 and SDI 2 input signal can be output from SDI 3 and SDI 4 respectively.

• Headless remote operation using VNC for MPX2 mode
  • Remote 8 tile operation using VNC in 8 tile mode is supported without the need for an external monitor or monitor emulator attached.
  • Note: MPI2 and MPS models still require an external monitor or monitor emulator for remote operation using VNC in 8 tile mode.

• MPS/MPD model support
• 8 trace Tile/Dual Display including eight 4K trace tiles
  • 8 trace tiles display is supported with dual display configuration.
  • Trace applications with 4K signals could be assigned to any tile.

• ARIB Closed Caption decode
  • ARIB TR-B24 standard is supported to decode.
  • HD/SD/Mobile captions can be simultaneously decoded.

• AES Status Display for SDI
  • AES/EBU header information in SDI embedded audio can be displayed.

• YCbCr 4:2:2 1080p 23/24/25/29/30 over 2110-20
  • Slow frame 422 formats over ST2110-20 are added.

• PTP time display on Status Bar
  • User selectable either PTP or RTC.

Release Notes – V3.1.1

Installation Instructions